The Hurst® Roll/Control®, Line/Loc® kit for your 87-93 Ford Mustang (w/out ABS) is primarily used in drag racing to lock the front wheels allowing for more consistent burnouts when heating up the tires to make a pass. This kit comes with all the necessary parts needed to easily install a Hurst Line/Loc system on your vehicle. Includes a stainless steel Roll/Control valve, brake line, fittings, lighted momentary switch, bracket, wiring, and much more. Rigorous testing has proved a 1/100,000 of a second release time and vibration tests have seen up to 30 G's applied without mechanical failure.

The advanced quality design utilizes a stainless steel valve assembly for ultimate corrosion resistance. Other features include a fully enclosed epoxy-molded electrical coil for reliability, an attractive finned aluminum housing that helps dissipate heat, and a wider lightweight base that provides better mounting stability and 150-micron screen-filtered ports to prevent contamination. The Roll/Control Kit is field serviceable for cleaning or rebuilding and comes with an extra threaded port for a separate bleeder or brake line pressure gauge. The kit also includes a snap-action switch, indicator light, 4-amp fuse, mounting screws, and installation instructions.

Note: Not recommended for use as a parking brake, or for longer than 60 seconds maximum at any one time.

Features:
The Hurst® Roll/Control®, Line/Loc® kit for your 87-93 Ford Mustang (w/out ABS) is primarily used in drag racing to lock the front wheels allowing for more consistent burnouts when heating up the tires to make a pass. This kit comes with all the necessary parts needed to easily install a Hurst Line/Loc system on your vehicle. Includes a stainless steel Roll/Control valve, brake line, fittings, lighted momentary switch, bracket, wiring, and much more. Rigorous testing has proved a 1/100,000 of a second release time and vibration tests have seen up to 30 G's applied without mechanical failure.

The advanced quality design utilizes a stainless steel valve assembly for ultimate corrosion resistance. Other features include a fully enclosed epoxy-molded electrical coil for reliability, an attractive finned aluminum housing that helps dissipate heat, and a wider lightweight base that provides better mounting stability and 150-micron screen-filtered ports to prevent contamination. The Roll/Control Kit is field serviceable for cleaning or rebuilding and comes with an extra threaded port for a separate bleeder or brake line pressure gauge. The kit also includes a snap-action switch, indicator light, 4-amp fuse, mounting screws, and installation instructions.

Note: Not recommended for use as a parking brake, or for longer than 60 seconds maximum at any one time.

More From This Category

DBA Front Street Series Brake Hose, For Suzuki Alto GF 1.0L Petrol FWD Front L/H 7/2009 - 1/15, Kit

DBA Front Street Series Brake Hose, For Suzuki Alto GF 1.0L Petrol FWD Front L/H 7/2009 - 1/15, Kit

$30.45

DBA Rear Street Series T2 Brake Rotor, 259.8mm, For Volkswagen Golf MkV 11/03, Kit

DBA Rear Street Series T2 Brake Rotor, 259.8mm, For Volkswagen Golf MkV 11/03, Kit

$188.06

DBA Disc Rotor, T2 Slot, 245mm Dia., 53.8mm Height, 10mm Thick, 68 Centre Hole, For Audi R, Each

DBA Disc Rotor, T2 Slot, 245mm Dia., 53.8mm Height, 10mm Thick, 68 Centre Hole, For Audi R, Each

$133.60

DBA Rear Street Series Brake Hose, For Nissan X-Trail T30 2.5L Rear Hose L/H 10/2001 - 9/07, Kit

DBA Rear Street Series Brake Hose, For Nissan X-Trail T30 2.5L Rear Hose L/H 10/2001 - 9/07, Kit

$50.82